Skip to content
Appointment timing depends on ZIP code, route capacity, and appliance type.
Whirlpool kitchen and laundry repair. Clear estimates before any work begins.
Call (310) 448-6692

Whirlpool

Whirlpool Washer F8E6 Error Code

Book a Repair (310) 448-6692
Maya Ortiz Written by Maya Ortiz Appliance Repair Content Specialist Published October 20, 2026

Whirlpool

Code overview at a glance.

The facts for this Whirlpool error, a plain-language snapshot, and what to confirm against your model number.

Error code F8E6
Appliance Washer
Quick answer

F8E6 has different meanings by model: water detected on laundry towers, lid open or no hot water on top loaders.

Model note: Whirlpool reuses codes across series and model years, so F8E6 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.

Whirlpool

What this code may mean.

A plain-language reading of the code — always confirm against your model’s documentation.

F8E6 means water detected on towers, and lid open or no hot water on top load washers.

The meaning of F8E6 depends on the washer. Whirlpool’s product help describes two cases.

Laundry tower washer section

The potential cause is “water detected.” Reset the control by keeping the washer disconnected from power for 5 minutes. If the code comes back, schedule service.

Top load washers

Depending on the model, F8E6 means one of two things:

  • The lid was open during the soak cycle. Close it and the cycle resumes.
  • No hot water was detected. Work through the checks below.

If hot water was not detected

  1. Look at the hoses. The code can mean the cold hose is on the hot inlet and the hot hose on the cold inlet. Reverse them and run another cycle.
  2. Open both the hot and cold water valves fully. Both inlet hoses must be connected for the washer to work properly.
  3. Cycle power to reset the control. Unplug the washer for 5 minutes, then plug it back in.

Related codes

  • F8E5: water supply reversed
  • F8E7: steam valve
  • F8E4: flow meter

Whirlpool washer service in Los Angeles

When F8E6 will not clear, call (310) 448-6692 or open the washer repair page. Have ready the code, whether it is a tower or a top loader, the model number and what you changed at the hoses and valves.

Source: Whirlpool Product Help: F8E6 Error Code; Whirlpool Product Help: F8E6 – Error Code

Whirlpool

Safety warning before you continue.

Stop immediately if you notice smoke, sparks, a burning smell, gas odor, or water near electrical parts.

Important

Do not attempt repairs involving electrical components, gas, water lines, refrigerant or sealed systems. Unplug the appliance if it is safe to reach the outlet, and leave internal diagnostics to a qualified technician.

Whirlpool

Seeing this code on your appliance?

Book an Whirlpool appliance service visit for a clear estimate and approval before any repair.

Experienced technicians, clear diagnostics, and workmanship coverage on completed repairs.

Book a Repair (310) 448-6692

Whirlpool

Ready to restore your Whirlpool appliance?

Book a repair online or call us — clear estimates, approval before any work, and a workmanship warranty on completed repairs.

Book a Repair (310) 448-6692

Whirlpool

Tell us what’s wrong — we’ll take it from there.

Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.

Prefer to call? (310) 448-6692
  1. Share the symptom Tell us the Whirlpool model and what’s going wrong.
  2. Confirm a window We’ll schedule a visit that fits your day.
  3. Approve before work You get a clear estimate — nothing starts without your OK.
Phone (310) 448-6692
Email info@whirlpoollosangeles.support
Hours Mon–Sat: 8:00 AM – 7:00 PM
Service area Serving Los Angeles County and Orange County.
Response time Appointment timing depends on ZIP code, route capacity, and appliance type.
(310) 448-6692 Book a Repair